All Products
Reverse Osmosis Chemicals is mainly utilized in the RO membrane layer system ， Antiscalant chemicals are utilized to avoid the scaling & fouling of the RO membrane layers. The range may contain mineral fouling such as calcium sulfate, calcium carbonate, barium sulfate, silica, calcium fluoride, and strontium sulfate.
The Antiscalant application needs to be done before getting to the RO membranes to separate sulfate precipitates, calcium carbonate, and various other mineral fouling. It is a very effective antiscalant for waters with LSI as much as 2.7, Iron up to 1.4 ppm in decline, Silica as much as 175ppm (or mg/l), High SDI. It works with the ALSTAFLOC series of coagulants and also flocculants (polyelectrolytes).
Antiscalant chemicals can refine inferior quality feed water at really high prices of recuperation. When utilized effectively, Antiscalant expands the time between membrane cleansings from a few weeks to years in some cases. Without Antiscalant, RO membrane systems would not be as successful in offering the water therapy market.
Trick Features and also Benefits
1.Effective range inhibition
2.High recuperation rate
3.Low Chemical dose
4.Economical
5.Minimized frequency of membrane cleaning
6.Effective Iron fouling control by sequestration
7.Totally organic as well as eco-friendly
8.Compatible with all kinds of membrane layers Ecofriendly antiscalant water therapy chemicals
technical requirements Application：
as well as Dosage vcycletech’s RO Antiscalant, is dosed directly to the RO feed water container or feedwater line (after pretreatment) at the minimum recommended dose of 1ppm and also maximum dose at 15ppm, subject to inlet water high quality, as well as specifications, is respect to Calcium Hardness, Iron, TDS, Alkalinity, pH, and also silica material. High alkalinity and also firmness can be regulated by dosing 4-5ppm of item. However, when it comes to the high iron web content of about 0.5 to 1.0 ppm, the application needs to be increased by 10-15ppm for supporting Calcium. At about 10-15ppm dosage, vcycletech’s RO Antiscalant can fully prevent iron and calcium, and silica approximately 175ppm. For greater silica material ALKRO HS40 need to be made use of.
Taking care of procedures and precautions
Correct human safety and security items such as Sprinkle safety glasses, lab coats, vapor respirators, handwear covers, and boots should be worn while handling and using chemicals. Sprinkles on the skin need to be cleaned off with water right away. In case of splashing right into the eyes, flush it with fresh water and obtain medical focus. Should not be injected. Please refer to MSDS for even more information.
Storage
This product needs to be kept in original containers in a great and also dry area, away from sources of warmth, fire, and also direct sunlight. Please describe Technical Data Sheet, Label, and MSDS for more details and life span.
Q: What is the distinction between Flocon 260 Antiscalant/Dispersant as well as Coagulant?
Flocon 260 Antiscalant is used to keep water solidity from speeding up throughout reverse osmosis therapy of water. The antiscalant likewise contains a dispersant, preventing iron or aluminum in water from reacting with the antiscalant and making it ineffective. Coagulant, on the other hand, works just the opposite. It is used to cause the suspended solids present in water to coagulate and settle out. By coagulation, we indicate that the wonderful bits of put-on-hold issue come together to end up being a larger collection, which will certainly clear up a lot more easily than the smaller suspended particles. The fine put-on-hold fragments in the water generally have an electric charge. The coagulate helps with eliminating the fee, permitting the particles to coagulate as well as resolve. Basically, a coagulant is made use of to eliminate put-on-hold solids. In the membrane layer procedure, coagulants are used only in rare situations. Numerous coagulants can be unsafe to the membrane layers. Coagulants are frequently used in community water treatment systems. Basically: Antiscalant is used for hardness, which is liquified in the water, and also coagulant is made use of for put on hold solids.
Q: We are application a cationic coagulant before sand filter in our saltwater desalination RO pretreatment system. Meanwhile, Flocon 260 (anionic) is dosed after the sand filter. I wonder whether these 2 chemicals might respond as well as cause fouling on the RO membrane layer.
Flocon 260 is commonly not suitable with cationic polymers. If we knew the precise polymer you are making use of, we would certainly have the ability to provide a guaranteed answer. Different Antiscalants might be made use of (FLOCON 40). However, we will certainly require a full water evaluation to identify whether this will work. The FLOCON 40 does not use much range control for the majority of the ‘sulfite’ ranges.
Q: Just how does antiscalant benefit a reverse osmosis water therapy application?
An antiscalant is a pretreatment infused right into the feedwater before the feedwater gets in the RO membrane layers. Its presence delays the reaction between calcium magnesium as well as bicarbonate. This results in scale not creating as the RO is cleansing the water. As the water’s duration in the membrane layer system is relatively brief during the treatment, scale development is stopped.
Q: Can extreme Antiscalant nasty the membranes?
Extreme antiscalant can trigger fouling of the membrane. This fouling can be cleaned by purging the membrane layers with water at a pH of 2-3. Antiscalant (organo-phosphonate) and AM-88 (salt meta-bisulfite for dechlorination) are sometimes utilized for pretreatment. In this case, exist any chemical reactions that would certainly create fouling of the membrane layer? There is no chemical reaction between the two chemicals.
Q: What are the dose rate and approach of injection for Flocon antiscalant?
The quantity of Flocon called for to prevent range development relies on the degree of supersaturation of the insoluble salts at the point of highest possible concentration in the system. The degree of supersaturation, in turn, depends upon the focus of the ionic varieties in the feedwater, the total salinity of the feed, the temperature of the feedwater, the percent of the feedwater recuperated as penetrate, and also the kind of membrane utilized for the application.
Usage soft water or RO permeate to blend with Flocon.
Dosage Technique Flocon ought to be included in a membrane system before the final cartridge filter.
If media filtration or turned-on carbon is used, Flocon should be used after these therapy stages. Flocon needs to be delivered by dosing pump from a dilution tank, direct from the drum or a bulk storage space facility, right into the feedwater at a price determined by the membrane system’s size, the recommended dosage price, and the delivery range of the application pump.
It is suggested that the dosing pump be readjusted by the stroke length while keeping stroke regularity at a high level to attain an even distribution of the Flocon in the membrane layer system feedwater.
CARE - Organic Task: Flocon has a preservative that is effective approximately a dilution of 1 component Flocon to 15 parts of system permeate water. General routine cleansing of the dosing system is advised as part of the prepared maintenance program.
We are a professional supplier of reverse osmosis chemicals. Our factory has obtained most of the certifications for producing high quality and economical reverse osmosis chemicals, and every production step is supervised by professional quality inspectors for each production step, for more information, please contact us.
